Estate of Tim Payne (dec)

Farm Equipment

JD 8100, JD 5200, IH 1586, (2) IH 1066, IH 574, IH 856, Case 885, Chandler 14′ spreader mounted on trk., Gleaner A II, NH C190 track skid steer – nr, Bobcat T300, Amadas Reel Rain, JD 5830 self-proplled silage cutter



Began: 09/28/19 at 10:00 AM EDT
Location: 1265 Payne’s Dairy Rd., Taylorsville, NC 28681



SATURDAY 28th SEPTEMBER 2019 – 10:00 AM


Directions: Being on Hwy. 64, 4 miles east of Taylorsville or 13.4 miles west  of Statesville, @ stoplight, go south on Millersville Rd. 3 mi., left on Payne’s Dairy Rd.,  go 1 mile to sale site. Watch for auction signs.
Sale Site Address: 1265 Payne’s Dairy Rd., Taylorsville, NC 28681

John Deere 8100, 4×4, SN-RW8100P004931, powered by 160 hp, 6-cyl. diesel, 16-speed w/ powershift transmission, 540 & 1000 shift-on-the go pto, differential lock, ps, (3) sets dual remote hyd. outlets, cab, 480/70R30 front tires, 20.8R42 dual rear tires, 487 hrs. showing, believe to have approx. 9000 hrs.

John Deere 5200, SN-LV5200E621193, powered by 40 hp, 3-cyl. diesel, 9 speed w/ 3×3 transmission, differential lock, ps, 540shift-on-the-go pto,(2) sets dual remote hyd. outlets, 2 post roll guard, canopy, 7.50-16 front tires, 14.9-28 rear tires, 4141 hrs., runs, brakes seem to be dragging.

IH 1066 Turbo, SN-2610172U037260, powered by 116 hp 6-cyl. diesel, 8 speed w/ hi-lo transmission, ps, 540/1000 shift-on-the-go pto, (2) sets  dual remote hyd. outlets, 11-16 front tires, 20.8×38 rear tires, hours unknown, runs ok.

IH 1586, powered by 161 hp 6-cyl. diesel, 3 speed w/ hi-lo transmission, differential lock, ps, 540/1000 shift-on-the-go pto, (2) sets dual remote hyd. outlets, cab, 11-16 front tires, 20.8-38 dual rear tires, fair rubber, runs ok.

IH 1066,  powered by 116 hp 6-cyl. diesel, 4 speed w/ hi-lo T/A transmission, ps, 540/1000 shift-on-the-go pto,(2) sets dual remote hyd. outlets, cab, air, no tires, unknown hours, been crashed, front end broke, right rear axle housing broke, engine should be ok, broke oil pan.

IH 574, powered by 52 hp, 4-cyl. diesel, 4 speed w/ hi-lo transmission, ps, 540 shift-on-the-go pto, single  remote hyd. outlet, 7.50-16 front tires, 16.9-28 rear tires, fair rubber, w/ front loader and rear pto drive winch, running.

IH 856, 100 hp,6-cyl. diesel, standard transmission, w/TA, ps, tri-cycle front end, approx. 5800 hrs., pto stays on, engine runs good, 1-owner, Tim Payne’s dad bought tractor new to the farm.

Case 885, SN-B650220B015884, powered by 72 hp 4-cyl. diesel, 8 speed w/ hi-lo T/A transmission, differential lock, ps, 540/1000 shift-on-the-go pto, (2)sets dual remote hyd. outlets, 7.50-18.00  front tires, 18.4-30 rear tires, unkown hrs., runs.

1989 Kenworth Model T600A day cab w/ Cat 3408 engine been rebuilt, 

not completely reinstalled, Motor is back in and running like a Cat, Fuller transmission, 2-speed rear end, 465,433 miles

1977 IH Model F-5070 Paystar Cummings, 8-cyl. diesel, 8-speed transmission, 2-speed rear axle, cab lights, ps, power brakes, am-fm radio, west coast mirrors, 11.4-25 Spokes front & rear, dump, dual tandem, 19.5 ‘ body, mileage unknown, 19.5 ‘ x 68 “ steel dump, engine runs, no clutch.

1984 Ford 700, 8-cyl. diesel, Cat 3208 engine, 13-speed transmission, 2-speed rear axle, ps, am-fm radio, west coast mirrors, 11R22.5 Budds front & rear,  30 gal. fuel capacity, 15’ single dump,  steel grain sides, 253,909 miles, may need head gasket.

1985 Chevrolet Custom 30, VIN-131077, 350 8-cyl. gas 4-speed transmission, cab lights, ps, power brakes, am-fm radio, west coast mirrors,  Budds front & rear, 12’ dump,  16” sides, 69,407 miles, blown engine?

Chevy 3500 4×4 pickup, 454 8-cyl. gas, 4-speed transmission, ps, power brakes, am-fm radio, side mirrors, gooseneck hitch, 16” Budds front & rear,  201,949 miles, needs a fuel pump.

‘76 Mack dual tandem dump truck, 4×4, 28L-26 front tires, 14.9R24 rear tires,for parts, engine runs, needs a radiator.

Knight 8040 Pro Twin Slinger, manure spreader mounted on ‘92 Western Star, dual tandem axle truck, SN-929908, w/ 26’ wheel base, 8-speed transmission, 6-cyl. Cat diesel engine, 218,799 mi.

Chandler 14’ spreader mounted on ‘73 IH 1700, 8 cyl. gas, 4-speed transmission, 2-speed rear axle, am-fm radio, west coast mirrors, 9-20 Spokes, 25 gal. fuel capacity, single tandem, 14’ body, 30 “ unloading chain, at press time truck was not running .

Allis Chalmers Gleaner AII, 6-cyl. gas engine w/ 13’ grain head, been sitting a few years.

New Holland C190 track skid steer, SN-N6M443586, 1941 hrs., cab, air, heat, super boom lift, may need right side drive, cranks, hydraulic works, may need a bearing in right drive sprocket.

Bobcat T300 Skid Steer w/ tracks, engine seems complete, left track & drive in pieces inside shop.)

(3) Skid Steer hitch buckets & forks.

IH 175C track loader, SN-4290004U003642, 2-speed w/ hi-lo gear, w/ bucket.

IH TD25E Bulldozer, 2-speed, needs turbo charger and exhaust manifold, under carriage looks 60%, 13’, 6-way blade, runs.

12’ Root rake, 11-shank, 12 “ on center shanks, fits 175C.


Amadas Model C1375G5 Reel Rain with Mdl. 11 gun cart, Nelson 150 gun, w/ Honda

gas,  hose rewind, nice  .

Houle pto irrigation pump 6 “ in, 4” out, remote hydro primer, SN-1501-030723-R

Badger BN185, lagoon pump agitator.

Approx 400’, 6”, 30’ sections, irrigation pipe, dual connect.

Approx. 2000’ Rainway irrigation pipe, 4”  CamLock.

RainBird 205G Gun,

Nelson 100 Gun on Stand.

(3) RainBird 80B Sprinklers.



IH   V-Ripper, 12’, 5-shank,4’ spacing between shanks.

International shank soil saver, 13’, 18-blade, 9” spacing front , rear shanks, trailer-type.

Massey Ferguson 144, 4-row spring shankcultivator, 13’ 3-pt.

IH 475, 20’, 56-blde hydraulic fold disc,  7” spacing, tandem wheels, trailer-type.

IH 28, 12’ disc harrow , tandem axle, heavy duty, pull type.

IH 4×16 bottom plow, 3-pt.

Massey Ferguson dual spike wheel tilavator, 3-pt., 14 ‘

Big Ox 8’ scrape Blade, 3-pt.

Oliver 14’ dual spike wheel tilavator,3-pt.

John Deere 5-bottom plow, 3-pt.

Massey Ferguson single chisel plow, 3-pt.

Kinze 3000, 6/11-row, no-till planter, 6-row 30”, 11-row 15”, no-till coulters w/trash wheels.

Case 5400 no-till drill w/ front coulter caddie, 15’,  set on 7 “ rows, 26 drops, pull type.

Oliver 2-row planter, 3-pt.

Dunham Lehr Cultimulcher, 10’, double rolls, shanks, pull type.

Brillion Cultipacker, 9’, pull type.



John Deere 5830 self-propelled silage chopper, hydro drive, SN-EO5830X810417, 4-speed, 3,007 hrs., operates as it should.

Kemper Model 4500, 6-row rotary  head.

John Deere Direct Cut Haylage 13’ cutter head.                      

John Deere Windrow, SN-476404E, 7’, heavy duty.                  

Gehl 1870 TDC round baler, 5×6 electric twine tie,

NH 855 Chain Bar hay baler, airbag tensioners, auto chain oiler, double arm hydraulic twine tie, field ready

New Holland 256 5-bar hay rake

John Deere 336 square balerw/hydro  bale thrower.

John Deere 1320 flail mower, 7’ , pull type.

Ford 14-92 sickle mower, 3-pt.

M&W 10-wheel hydraulic fold hay rake, pull type.

IH 950 mixer/grinder

Forgo telescoping remote dump wagon on pull-type model 286, running gear.

Knight 3030 Reel Auggie feed mixer wagon, pto drive, single axle, needs tires, a parts machine.

Gehl Model MS1322 scavenger spreader, parts, minus tires.

John Deere 920 Moco flail disc  mower, for parts.

Knight Protwin 8018 Slinger manure spreader.

Hesston 2000 tank liquid spreader, pto drive, front  unloader, 2-axles, 13.50-16.1 flotation tires.

(2) Badger BN338 3000 gal. liquid manure tankers, rear spreaders,  lower exit, tandem axles, 21.5L-16.1 flotation tires, pto drives

Several hay wagon running gears, (2) IH Model 315 & (1) John Deere 965.

Shaver hydraulic post driver, 3-pt.

(2) Harvester silos: (1) 70 ‘ tall, 17 ‘ wide, (1) 36 ‘ tall, 18 ‘ wide

(2) Long grain bins, approx. 7,000 bu. each w/ shared dryer, good condition.

Long  approx. 6,000 bu. grain bin w/ dryer w/ 12’ upright unloading auger.

Hutchinson 8” grain unloading angle     auger head, 5 ‘ long, w/ 5 hp motor, looks like new.

Long 7’, 8” long angle unloading auger, 5 hp motor.

Brock approx. 150 bu. upright feed bin w/ 12 ‘ long, 4-” unloader.

(2) Brock approx. 300 bu.  upright feed bins w/ unloading augers.

Brock  approx. 1000 bu. upright feed bin w/ 3 “ PVC unloading augers.

Harvester unloading head.

60’, 8” grain auger,  pto drive, bent.

Complete 8-cow milking parlor, stainless pipe, auto-set feeders, 8 milkers.

Gardner Denver Model 4MR Vacuum pump, 7.5 hp.

Livestock gates.

Cattle corral panels.

10’ poly feed trough on galvanized frame.



Miller Mdl. OT 18’ x 8’ tilt top trailer, dual tandem axle, pintle hitch, 7.50-15 tires, air brakes, needs floor & tires.

14 ‘ x 6 ‘ livestock enclosed trailer, tandem axle, 2 “ ball hitch, 15” tires, (could stand TLC)

16 ‘ x 6 ½’ flat bed trailer, tandem axle, no sides, 2 “ ball hitch, 8-14.5 tires, (TLC here could be used)

16 ‘ x 6 ‘ shopmade livestock trailer, dual axle, 6 ‘ sides, 2 “ pin hitch, 16” tires.

14 ‘ x 6 ‘ all steel dual axle trailer, no sides, pin hitch, minus  tires, (could be brought back).

6 ‘ x 3 ‘ calf livestock trailer, single axle, 3 sides, 1 7/8 ball hitch, 13 tires, homemade, good condition.

20 ‘ x 8 ‘ plus 9 ‘ over neck flatbed trailer, 3 axle,  gooseneck hitch, 8-14.5 tires, homemade, fair condition.

35 ‘ x 8 ‘semi-hitch log trailer, dual tandem axle, 6 ‘ sides, poles, semi-hitch, 10-R20 tires, has telephone poles on it, (TLC could work here).

7 ‘ x 14 ‘ single Axle Trailer Frame, pin hitch.

Yellowstone travel trailer, 22 ‘ long, tag-along, for parts.



Degelman Mdl. 12-46/57 front mounted 6-way blade, operates from tractor remotes, mounted on JD 8100, buyer to take off.

Hole Digger, 3-pt.

6,000 gal.  poly nitrogen tank.

300 gal. poly tank ground drive double sprayer, 12 ‘, pull-type, on 12.5L-16 flotation tires.

900 gal. poly tank, and others.

Several stainless sinks.

Several old milk cans.

PVC pipe & fittings.

10 ‘ x 2 ‘ poly culvert pipe.

Kellogg American air compressor, 3-phase, 80 gal.

Ingersoll-Rand Mdl. 242-5D T30 air compressor.

Winco pto generator, 3-pt.

Assortment of 2 “ lumber.

New 14.5 tires mounted on rims.

(2) Large air compressors for parts.

Large roll of new 5/8 “ cable.

Several large steel fuel tanks: (1) 10.6 x 10.6 x 30 ‘, (1) 8 ‘ x 8 ‘ x 30 ‘, (2) 5 ‘ x 5 ‘ x 12 ‘

Electric  chain hoist.

(2) Large box fans.

Grinders, drills, etc.

Hobart wire spool welder, 300 amp.

Miller CP200 wire spool welder.

Aceteyle cutting torch.

Carolina metal cutoff bandsaw

Parts washer.

Pure double sided porcelain round sign, 6 ‘round, has approx. 20’ tapered cast iron finial top pole, used to hang @ Payne’s Store @ Payne’s Crossroad.

Several steel racks and steel.

Several bolt bins w/ bolts & nuts.

Several trailer axles.

Johnson energy wood stove, large – not sure but believed to be home-made out of 55 gal. barrels.

Engine Hoist on wheels 9’x8’, w/Yale 2-ton chain hoist.

Several tires of assorted sizes.

10-ton  hydraulic floor jack & others.

60,000# hydrualic  shop press.

Engine stand.

Cherry picker.

Large radiators and other truck parts.

Engines and transmissions.

Assortment of new oil, fuel, air filters.

Milwaukee PortaBand saw.

Tool chests w/ various tools, wrenches, sockets, drill bits, air wrenches, etc.

New roller chains.

Lots of service manual books.

Pipe threader.

Several steel tables, work benches with vises.

Suzuki 4×4 and Honda 4-wheeler (not running).

Electric motors.

Engine stand.

Ciba-Geigy field pak chemical tank w/ 12-volt pump.

Honda Cat Model 6DX40G1 pressure washer, 13 hp, gas.

Gas log splitter on single axle trailer.

Enco Model 20AP upright drill press, ¾ hp.

Dayton double grinder, ¾ hp, and others.

KEF cutoff saw, 14 “

Several electric hand tools

Capri Bayliner Boat on 2-axle trailer, 19 ‘, parts.

Equipment from another Farmer:

Amadas Model A1375G5 Reel Rain, SN-390484, w/ 1,100’,  4”  hose, Nelson 150 gun, Honda gas rewind engine.

2001 Hudson 24’, 8-ton equipment trailer, w/ beaver tail & spring ramps, pintle hitch, dual tandem axles, 8:75 R16.5, electric brakes.

Bobcat 853, 4-cyl. Kubota engine, 12×16.5 tires w/ loegering tire chains, 5970 hrs.,  handles well.

Auctioneer’s Note: Be here Auction Day! At press time many items still to be found or being repaired. This sale will offer equipment in various stages –from ready to go to job & work to equipment that needs some wrenches turned so there will be lots of opportunities on this auction to fit a lot of needs.


Sale Manager: Eli Detweiler Jr.: 336-848-8165


Bring your trucks & trailers sale day– (2) loaders will be there to assist if –U- need on sale day.


Check web for updates & extra photos.


Lunch available.



Silage Pit Covers, 23×62, these are the kind that are green, keeps the plastic from taring, will also work for livestock & greenhouse shades.

IH 454 4-cyl. gas, 540 pto,  w/front end quick attach loader,  

Long 360. 38 hp 3-cyl. diesel. 

Long 445 3-cyl. diesel, (for parts)

‘85 Chevrolet Custom Deluxe pickup, 4×4, 350 V8,  4-speed manual transmission, short bed, runs but needs rear engine seal.

’64 Chevrolet C60 292 gas, 4-speed transmission, 14’dump, rock sides,  single axle, rock sides, 292 needs work.

New Holland Mdl. 467  hay bine.

New Idea Mdl. 394 side hay rake.

New Holland Mdl.  846 round baler, with auto twine tie wrap. 

New Holland Mdl. 156 2-basket hay tedder, pull type.

Shopmade  14’ x 6’  tandem axle stock trailer.

Rotary mower, 5’, 3-pt.

Ford 5’ box blade.

Ford 345D Industrial tractor loader, 2 wheel drive 3-cyl. diesel engine, 4 speed with hi lo range shuttle shift transmission, 5963 hours. working tractor. Serial 441846

4-n- 1 bucket to fit loader
4-row cultivator, 3-pt.
Ford 8000 2 wheel drive tractor, cab w/heat & fresh air, 6-cyl. diesel, 8 speed trans with hi-lo,(2) sets remotes, 18.4 -38 rear tires, 10-16 front tires, 5429 hours. A clean original 2 owner tractor that runs nice.
Bush Hog 12′ point mower, with 4 wheels like a finishing mower.3-pt.
9 spring shank tiller, 3-pt.
Massey Ferguson 6′, 20 blade tandem disc harrow, 3-pt.
1-bottom  plow, 3-pt.
1 row cultivator, 3-pt.
1- row potato plow, 3-pt.

Terms & Conditions:  All purchases must be paid for sale day. All property sells as is where is with all faults, with absolutely no warranties implied or expressed in any way.  All Serial Numbers, mileage & hrs. unverified. All info printed in brochure is believed to be correct but not guaranteed.  The auction company reserves the right to offer property in separate sales, combinations thereof or as a whole.


Payment in Full Day of Sale – Cash or Check  – No debit or credit cards


Directions: Being on Hwy. 64, 4 miles east of Taylorsville or 13.4 miles west  of Statesville, @ stoplight, go south on Millersville Rd. 3 mi., left on Payne’s Dairy Rd.,  go 1 mile to sale site. Watch for auction signs.

Sale Site Address: 1265 Payne’s Dairy Rd., Taylorsville, NC 28681

Click on any image to view larger.

Click on any image to view larger.

JD 5830 self-propelled TD 25E bulldoze JD 8100 &  12' blade will sell separately NH C190 IH 856 = 1-owner  - 5800 hrs.
Kinze 6/11 row - reach your planting goals JD 5200 Case 5400 n-till Knight 8040 Pro Twin Slinger on '92 Western Star IH 175 C track loader
Amada 1300 w/Nelson 150 gun Huston 24' , 8-ton Bob 853 Amadas Reel Rain

Click on any image to view larger.

E. B. Harris Inc. Auctioneers

3200 NC Hwy. 58 WARRENTON, NC 27589

Your auction should be printing now. If not, please click here.